Skip to content

US Based Company

Ships From USA Warehouses

100,000+ Lights Shipped

Trusted by Contractors Nationwide

Contractor Pricing

Bulk Discounts Available

Orders Before 2PM

Ship Same Day

Expert Support

Lighting Specialists

Lumens vs. Watts and LED Efficacy

Lumens vs. watts: LED efficacy (lumens per watt) explained

For decades, people bought light bulbs by watts. A 100W bulb was brighter than a 60W bulb, and a 400W metal halide was the standard warehouse light. With LED, watts no longer tell you how bright a fixture is. This guide explains lumens, watts, and efficacy, and how to compare LED fixtures correctly.

Gymnasium lit by LED high bays

Lumens measure light

A lumen is a measure of the total visible light a fixture produces. More lumens means more light. When you compare two fixtures for the same job, compare lumens first.

  • A 4 ft LED shop light: roughly 4,000–6,500 lumens
  • A 2x4 LED troffer: roughly 4,000–7,500 lumens
  • A 150W UFO high bay: roughly 20,000–23,000 lumens
  • A 150W LED shoebox area light: roughly 20,000–25,000 lumens
  • A 300W LED flood light: roughly 39,000–45,000 lumens

Watts measure power

Watts measure how much electricity a fixture uses. Lower watts for the same lumens means lower energy bills. A 150W LED high bay can replace a 400W metal halide fixture that actually draws about 458W including its ballast.

Efficacy: lumens per watt

Efficacy is lumens divided by watts. It tells you how efficiently a fixture turns electricity into light.

  • Incandescent: about 10–17 lm/W
  • Halogen: about 15–25 lm/W
  • Mercury vapor: about 30–50 lm/W (system)
  • Metal halide: about 60–80 lm/W (system), less as lamps age
  • Fluorescent T8: about 80–95 lm/W (system)
  • High-pressure sodium: about 80–120 lm/W (system), but with very poor color
  • Commercial LED fixtures today: commonly about 120–160 lm/W

Many of our fixtures are rated around 130–150 lm/W. For example, our 2x4 LED troffer with clear cover is rated up to about 150 lm/W, and our 150W LED shoebox produces 22,500 lumens from 150W.

Fixture lumens vs. delivered lumens

Older lighting is often described by lamp lumens: the light from the bulb before it goes through the fixture. A metal halide fixture loses a large share of that light inside its reflector and lens, and sends much of the rest in directions you do not need. LED fixture lumens are measured for the whole fixture, and LED optics direct light where it is wanted.

That is why an LED fixture with fewer rated lumens can still put as much or more light on the floor than the fixture it replaces. Compare foot-candles on the target surface when you can.

Lumen depreciation

All light sources get dimmer over time. Metal halide lamps can lose 30–40% of their output well before they burn out. LED fixtures lose output slowly; their life is usually stated as the hours until output falls to 70% (L70). See LED lifespan, L70, and warranties.

How to compare LED fixtures

  1. Match lumens to the job. Use how many lumens do I need?.
  2. Compare efficacy for energy cost. Higher lm/W means lower bills.
  3. Check color temperature and CRI. See CRI explained.
  4. Check listings such as UL, ETL, and DLC. See UL, ETL, and DLC listings explained.
  5. Check the warranty. Our fixtures carry a 5-year warranty.

Quick wattage equivalents

  • 400W metal halide high bay: about 150W LED
  • 1000W metal halide: about 300–400W LED
  • 250W metal halide: about 80–100W LED
  • 175W metal halide wall pack: about 40–60W LED
  • 2-lamp 4 ft T8 fluorescent: about 20–30W LED
  • 3-lamp T8 2x4 troffer: about 35–50W LED

See the metal halide to LED replacement chart, HPS and mercury vapor to LED, and fluorescent to LED conversion.

Why LED efficacy keeps improving

LED efficiency has improved steadily for years as chip, phosphor, and driver technology have advanced. Fixtures available today often produce noticeably more lumens per watt than those from just a few years ago. That is why replacing early LED fixtures can sometimes make sense, and why DLC efficacy requirements rise over time.

Driver efficiency and power factor

A fixture's efficacy includes losses in the driver, the electronics that convert line power to LED power. Good drivers are around 90% efficient or better. Power factor (how effectively the fixture uses the current it draws) is usually above 0.9 on commercial LED fixtures. Total harmonic distortion (THD) under 20% is a common benchmark. These numbers matter most on large installations.

Example: comparing two high bays

  • Fixture A: 150W, 21,000 lumens, 140 lm/W
  • Fixture B: 150W, 19,500 lumens, 130 lm/W

Fixture A gives about 8% more light for the same power. For 50 fixtures running 5,000 hours a year, you could get the same light from Fixture A at a lower wattage setting, saving several thousand kWh a year.

Example: same light, less power

You need 20,000 lumens per fixture.

  • At 130 lm/W, that takes about 154W.
  • At 150 lm/W, about 133W.
  • Across 40 fixtures at 4,000 hours a year, the difference is about 3,300 kWh a year.

Common mistakes

  • Buying by watts instead of lumens.
  • Comparing lamp lumens from old fixtures to LED fixture lumens.
  • Ignoring distribution; lumens in the wrong place do not help.

Warehouse lit with LED high bays

Frequently asked questions

How many lumens is a 100W LED?

At a typical 130–150 lm/W, about 13,000–15,000 lumens. Always check the product page.

Is higher lumens per watt always better?

For energy use, yes. But color quality, glare, distribution, and reliability also matter.

What does lm/W stand for?

Lumens per watt, the measure of how efficiently a fixture produces light.

Related

Lighting glossary · LED savings and payback · Warehouse lights · Parking lot lights · Lighting resources

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare