Skip to content

US Based Company

Ships From USA Warehouses

100,000+ Lights Shipped

Trusted by Contractors Nationwide

Contractor Pricing

Bulk Discounts Available

Orders Before 2PM

Ship Same Day

Expert Support

Lighting Specialists

HPS and Mercury Vapor to LED

HPS and mercury vapor to LED replacement guide

High-pressure sodium (HPS) and mercury vapor lights were the standard for street lights, parking lots, warehouses, and farm yards for decades. Many are still in service, buzzing orange or blue-white and drawing far more power than they need to. Replacing them with LED cuts energy use dramatically, ends lamp changes on tall poles, and makes everything look clearer. This guide shows typical LED equivalents and what to watch for when you convert.

Roadway at dusk with LED street lights

High-pressure sodium

HPS lamps produce a strong orange-yellow light, around 2,000K, with very poor color rendering (CRI around 20–25). Under HPS, a red car and a brown car look nearly the same, and faces are hard to recognize on camera. HPS is efficient at turning power into light, but much of that light is wasted because the fixtures spread it inefficiently, and the lamps lose output over time.

Typical HPS system watts

The ballast adds to the lamp rating. Typical system draw:

  • 70W HPS: about 90–95W
  • 100W HPS: about 130W
  • 150W HPS: about 190W
  • 250W HPS: about 300W
  • 400W HPS: about 465W
  • 1000W HPS: about 1,100W

Typical LED replacements for HPS

  • 70–100W HPS (wall packs, small area and street lights): 30–50W LED
  • 150W HPS: 50–80W LED
  • 250W HPS (street lights, small parking lots): 80–100W LED
  • 400W HPS (parking lots, high bays, roadways): 150W LED
  • 1000W HPS (large areas, sports, industrial yards): 300–400W LED

Because LED directs light where it is needed and renders color far better, the space usually looks brighter after conversion even at similar measured light levels.

Mercury vapor

Mercury vapor lamps give a blue-green white light and are the least efficient of the common HID types. They also lose light quickly with age. The U.S. Energy Policy Act of 2005 banned the manufacture and import of mercury vapor ballasts starting in 2008, so replacement ballasts are no longer available new. Any mercury vapor fixture still running should be replaced with LED, not repaired.

Typical LED replacements for mercury vapor

  • 175W mercury vapor (barn lights, yard lights, wall packs, about 205W system): 40–60W LED
  • 250W mercury vapor (about 285W system): 60–80W LED
  • 400W mercury vapor (about 455W system): 100–150W LED

Old dusk-to-dawn "yard lights" on farms are often 175W mercury vapor. Our LED barn lights and dusk-to-dawn lights are direct upgrades, many with built-in photocells.

Farm yard and barns lit at dusk

Choosing the right LED fixture

What to check before you convert

  1. Lumens, not watts. Compare the old lamp's useful output with LED fixture lumens. LED typically needs one-third to half the watts.
  2. Voltage. HID fixtures often run on 208V, 240V, 277V, or 480V. Confirm the LED fixture's voltage range; see 277V and 480V LED lighting.
  3. Mounting. Match the arm, slip fitter, or wall box; see mounting options.
  4. Distribution. Choose the pattern that fits the site; see outdoor distribution types.
  5. Color temperature. 3000K is closest in warmth to HPS and preferred near homes; 4000K is common for roads and parking; 5000K for industrial yards and security. See the color temperature guide.
  6. Photocells and controls. Most outdoor fixtures should have a photocell or be on a time clock.
  7. Dispose of old lamps properly. HID lamps contain mercury and should be recycled.

Savings example

Ten 400W HPS parking lot lights (about 465W system) replaced with 150W LED, running 4,300 hours a year at $0.13 per kWh:

  • Old: 10 × 465W × 4,300 ÷ 1,000 = about 20,000 kWh, about $2,600 a year
  • New: 10 × 150W × 4,300 ÷ 1,000 = 6,450 kWh, about $839 a year
  • Savings: about 13,500 kWh and $1,760 a year, plus no more bucket-truck lamp changes

See LED savings and payback for more examples.

Frequently asked questions

What LED wattage replaces a 250W HPS?

Typically 80–100W LED.

What LED wattage replaces a 400W HPS?

Typically 150W LED.

Can I still buy mercury vapor ballasts?

New mercury vapor ballasts have not been manufactured or imported in the U.S. since 2008. Replace the fixture with LED.

Will LED look different from HPS?

Yes. LED is white instead of orange and renders colors accurately. Choose 3000K if you want a warmer look closer to HPS.

Related

Metal halide to LED replacement chart · Street lights · Parking lot lights · Barn lights · Request a layout · Lighting resources

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare