Dark sky lighting, light trespass, and BUG ratings
Outdoor lighting should light the ground you own, not the sky or the neighbor's bedroom. Many towns now have outdoor lighting ordinances, and neighbors notice glare and spill quickly. This guide explains light pollution, light trespass, full cutoff fixtures, and BUG ratings, and how to plan outdoor lighting that meets local rules.

Three kinds of unwanted light
- Sky glow: light sent upward that brightens the night sky over towns and cities.
- Light trespass: light that crosses the property line onto neighboring property, roads, or windows.
- Glare: bright light in a person's field of view that makes it harder to see, especially for drivers.
All three waste energy, and all three can be reduced with fixture choice and aiming.
Full cutoff and fully shielded fixtures
A full cutoff or fully shielded fixture sends no light above the horizontal plane. Flat-lens shoebox area lights, many modern wall packs, and canopy lights are commonly full cutoff when mounted level. Fixtures with drop lenses, globes, or tilted mounts usually are not.
Tilting a fixture upward to push light farther defeats full cutoff, even with the right fixture.
BUG ratings
The IES BUG rating system scores outdoor fixtures on three kinds of stray light:
- B (backlight): light behind the fixture, which can spill over a property line.
- U (uplight): light above horizontal, which causes sky glow.
- G (glare): high-angle light in front of and around the fixture.
Each is rated 0 to 5, where 0 is the least. A fixture might be rated B2-U0-G2, meaning moderate backlight, no uplight, and moderate glare. Many ordinances set maximum BUG ratings depending on the zone and how close the fixture is to the property line.
Lighting zones
Many ordinances and model codes divide areas into lighting zones, from dark rural areas (lowest allowed light) to dense urban centers (highest). The zone sets limits on uplight, light at the property line, and sometimes total lumens per acre. Ask your local planning or building department which zone your site is in.
How to reduce light pollution
- Choose full cutoff fixtures and mount them level.
- Use the right distribution. Type IV fixtures at the property line throw light forward with little behind; see outdoor light distribution types.
- Add shields where fixtures near the property line still spill.
- Use only the light you need. Overlighting is the biggest cause of glare and sky glow. Use selectable wattage to dial it in.
- Choose warmer color temperatures near homes and natural areas. Many dark-sky guidelines recommend 3000K or lower.
- Use controls. Photocells, motion sensors, and after-hours dimming cut light when no one needs it; see photocells and motion sensors.
- Aim flood lights down. If you must light a sign or building face, aim from above when possible, and keep beams on the target; see beam angles.

Fixture choices for low light pollution
- Parking lots: flat-lens shoebox area lights mounted level.
- Building perimeters: full cutoff wall packs; see the wall pack buying guide.
- Walkways: bollards and shielded post-top lights keep light low.
- Canopies: recessed or flat-lens canopy lights.
- Streets: flat-lens LED street lights.
Converting old fixtures helps
Older drop-lens cobra heads, globe post tops, and non-cutoff wall packs often send a large share of their light sideways and up. Replacing them with full cutoff LED fixtures usually cuts sky glow and glare at the same time as energy use. See HPS and mercury vapor to LED.
Light trespass limits
Some ordinances limit how much light can cross a property line, measured in foot-candles at a set height above the ground at the line. Common limits near residential areas are quite low, often well under 1 foot-candle. To meet them:
- Keep poles back from the property line, or use Type IV fixtures that throw light forward.
- Add house-side shields to fixtures nearest the line.
- Lower the mounting height or wattage of the closest fixtures.
- Avoid flood lights aimed toward neighbors.
A photometric layout shows the light level at the property line before you install.
Curfews and after-hours dimming
Many ordinances and dark-sky guidelines call for reducing or turning off non-essential outdoor lighting after business hours. Options include:
- Time clocks that switch off decorative and sign lighting at closing.
- Dimming parking lot lights to a lower level overnight, with motion sensors to raise them when someone arrives.
- Keeping only security-critical lights at full output.
See 0–10V dimming and lighting controls.
Why warmer color temperatures help
Cooler, bluer light scatters more in the atmosphere and contributes more to sky glow. It also affects nocturnal wildlife more strongly. That is why many dark-sky guidelines recommend 3000K or warmer, and why some coastal areas with nesting sea turtles require special amber lighting. For most commercial sites near homes, 3000K is a good balance of visibility and low impact.
Checklist for an ordinance-friendly site
- Find your lighting zone and the ordinance limits.
- Choose full cutoff fixtures with BUG ratings that meet the limits.
- Mount fixtures level; avoid tilting.
- Use Type IV or shields near property lines.
- Use the lowest wattage that meets your light levels.
- Choose 3000K–4000K unless there is a reason for cooler light.
- Plan curfew controls.
- Get a photometric layout showing property-line light levels.

Frequently asked questions
What does full cutoff mean?
The fixture sends no light above the horizontal when mounted as intended.
What is a good BUG rating?
It depends on the zone and location on the site. U0 (no uplight) is a common requirement, with B and G limits set by how close the fixture is to the property line.
What color temperature is dark sky friendly?
Many dark-sky guidelines recommend 3000K or warmer.
Related
Outdoor distribution types · Parking lot lights · Security lights · How many lumens for a parking lot · Lighting resources