Beam angles for flood and sports lights
A flood light's beam angle decides whether it throws a tight spot of light a long way or spreads a wide wash across a nearby wall. Choosing the right beam angle is how you light a sign without lighting the sky, a building face from the ground, or a sports field from a tall pole. This guide explains beam angles, NEMA beam types, and which to use where.

What beam angle means
The beam angle is the angle of the cone of light from a fixture, measured to where the light drops to half of its center intensity. A 30° beam is narrow and concentrated; a 120° beam is wide and spread out.
Narrow beams put more light on a smaller area farther away. Wide beams spread the same light over a bigger area closer to the fixture.
NEMA beam types
Flood lights are often described with NEMA beam types, which group beam spreads by angle:
- NEMA 1: 10–18°, very narrow
- NEMA 2: 18–29°, narrow
- NEMA 3: 29–46°, medium narrow
- NEMA 4: 46–70°, medium
- NEMA 5: 70–100°, medium wide
- NEMA 6: 100–130°, wide
- NEMA 7: 130° and wider, very wide
How far a beam reaches
A simple way to estimate the width of the lit area: at a given distance, the spot is roughly twice the distance times the tangent of half the beam angle.
- A 30° beam at 50 ft lights a circle about 27 ft wide.
- A 60° beam at 50 ft lights a circle about 58 ft wide.
- A 120° beam at 20 ft lights a circle about 69 ft wide.
Wider spots at the same output mean fewer foot-candles on the surface.
Which beam angle to use
- Sports fields from tall poles: narrow to medium beams, often mixed: narrow beams for the far side of the field and wider beams for the near side. See the sports field lighting guide.
- Flagpoles, tall signs, and building features: narrow beams aimed up, with shields to limit sky glow.
- Building facades from the ground: medium beams placed back from the wall.
- Billboards and signs: medium to wide beams mounted close to the sign face.
- Parking areas and yards from a building or pole: wide beams, though an area light with a defined distribution is usually more even; see outdoor light distribution types.
- Security lighting near a building: wide beams, often with a photocell or motion sensor; see security lights.
- Landscape and trees: narrow beams for tall trees, wide beams for shrubs and walls; see landscape lighting.
Mounting and aiming
- Yoke (U-bracket) mounts bolt to a surface and let the fixture tilt.
- Trunnion mounts bolt to a cross-arm or pole bracket.
- Slip fitter mounts slide over a pole tenon.
- Knuckle mounts fit a junction box or ground stake.
Aim flood lights down whenever possible. Every degree above horizontal sends light into the sky and toward neighbors' windows. Shields and visors can trim stray light. See LED fixture mounting options.

Beam angle and glare
Narrow beams are intense at their center and can cause glare if someone looks along the beam. Keep narrow beams aimed away from roads, windows, and sightlines. Wide beams are less intense but spread more light where you may not want it. In both cases, aiming and shielding matter more than the fixture alone.
Example: lighting a building facade
Say you want to wash a 60 ft wide, 25 ft tall building face from fixtures set 20 ft out from the wall.
- A 60° beam at about 25 ft of throw covers a spot roughly 29 ft wide, so two or three fixtures spaced across the face give even coverage with overlap.
- A 120° beam from the same spot would spill well past the edges of the building and into the sky.
- A 30° beam would leave bright stripes with darker bands between fixtures.
Medium beams set back from the wall usually give the most even wash. Aim slightly below the top edge so light does not run off the roof line.
Example: lighting a sign
For a 20 ft wide sign face, fixtures mounted on arms 3–6 ft in front of the sign and aimed back at it work best with wide beams, so the light spreads evenly across the face from a short distance. Mounting above the sign and aiming down keeps light out of the sky and out of drivers' eyes.
Choosing output along with beam angle
Beam angle decides where light goes; lumens decide how much. When you narrow the beam on the same fixture, the light on the target gets brighter because it is concentrated on a smaller area. When you widen it, each square foot gets less. As a rough check, divide the fixture lumens by the area of the lit spot in square feet and multiply by about 0.6 to account for losses; the result is the approximate foot-candles on the target.
Common mistakes
- Using the widest beam for everything. Wide beams from far away waste most of their light.
- Aiming above horizontal. It causes glare and sky glow, and many ordinances prohibit it.
- Mixing color temperatures across a facade or field.
- Forgetting shields on narrow beams near roads and homes.
- Skipping the layout. For fields and large facades, a photometric layout sets the beam angles and aiming points that give even light.
Checklist before you order
- Measure the distance from the fixture to the target.
- Measure the width and height of the area to light.
- Pick a beam angle that covers the area at that distance with some overlap between fixtures.
- Choose lumens for the light level you need; see how many lumens do I need?.
- Choose the mount: yoke, trunnion, slip fitter, or knuckle.
- Confirm wet-location and IP ratings for outdoor use; see IP ratings and wet locations.
- Plan controls, such as a photocell or timer.
Frequently asked questions
What beam angle is best for a flood light?
It depends on distance and target. Wide beams (100–130°) for nearby areas, medium (45–70°) for building faces and signs, and narrow (under 30°) for long throws from tall poles.
What beam angle is best for sports lighting?
Usually a mix of narrow and medium beams, set by a photometric layout.
Can I change the beam angle of a flood light?
Not usually. Some fixtures offer interchangeable optics or visors. Choose the beam angle when you order.
Related
LED flood lights · LED stadium lights · Security lights · Dark sky and BUG ratings · Lighting glossary · Lighting resources