Skip to content

US Based Company

Ships From USA Warehouses

100,000+ Lights Shipped

Trusted by Contractors Nationwide

Contractor Pricing

Bulk Discounts Available

Orders Before 2PM

Ship Same Day

Expert Support

Lighting Specialists

Bollard, Pathway and Landscape Lighting Guide

Bollard, pathway, and landscape lighting guide

Walkways, plazas, courtyards, and landscaped areas need light that guides people safely without glare and looks good doing it. Bollards, post-top lights, and landscape fixtures keep light low and close to where people walk. This guide covers fixture types, light levels, spacing, and design tips.

Pathway lined with bollard lights

Bollard lights

Bollards are short posts, typically 3–4 ft tall, with light at the top that spreads outward along the ground.

  • Where: walkways, building entrances, plazas, parking islands, and drop-off areas.
  • Spacing: commonly about 10–20 ft apart along a path, depending on output and how even you want the light.
  • Light pattern: 360° bollards light all around; 180° bollards light one side, useful along a building or property edge.
  • Mounting: on a concrete footing with anchor bolts.

Browse LED bollard lights.

Post-top lights

Post-top fixtures sit on top of 10–16 ft poles. They light wider areas than bollards and add a decorative look to campuses, plazas, and streetscapes.

  • Spacing: commonly 40–80 ft apart along a walkway, depending on pole height and output.
  • Look: modern or traditional styles.
  • Glare: choose shielded post tops where light trespass is a concern.

Browse LED post-top lights.

Campus walkway with post-top lights

Landscape lighting

Landscape fixtures highlight trees, shrubs, building features, and signs.

  • Uplights and spotlights aim at trees and walls; narrow beams for tall trees, wide beams for shrubs and walls.
  • Path lights are short fixtures that light the edges of paths and beds.
  • Wall washers and flood lights light building facades and signs.

Browse LED landscape lighting and LED flood lights. See beam angles for flood and sports lights.

Light levels

  • Walkways and paths: about 0.5–2 foot-candles
  • Building entrances: about 5–10 foot-candles
  • Plazas and gathering areas: about 1–5 foot-candles

Even, low light is more comfortable and feels safer than bright pools separated by dark gaps.

Design tips

  1. Light the path, not the eyes. Keep fixtures low or shielded.
  2. Be consistent. Use one color temperature, often 3000K for walkways and landscapes.
  3. Light changes in grade. Steps, ramps, and curbs need extra light.
  4. Layer the light. Combine bollards for paths, post tops for wider areas, and landscape lights for character.
  5. Mind the neighbors and the sky. See dark sky and BUG ratings.
  6. Use photocells or timers so lights run only when needed; see photocells and motion sensors.

Durability

Outdoor fixtures must be wet-location rated. In public areas, choose sturdy die-cast housings and impact-resistant lenses; see IK impact ratings and IP ratings and wet locations.

Choosing between bollards and post tops

  • Bollards keep light low and soft, add a physical marker along the path, and avoid glare entirely for people walking. They need more fixtures for the same length of path.
  • Post tops cover more ground per fixture, light faces better for security cameras, and give a streetscape look. They need poles and taller foundations.
  • Many sites use both: post tops along main walkways and plazas, bollards at entrances, steps, and planters.

Example: lighting a 300 ft campus walkway

  • With bollards at about 15 ft spacing: about 20 bollards along one side.
  • With post tops on 12 ft poles at about 60 ft spacing: about 5–6 poles.
  • Light level target: about 1 foot-candle average, brighter at intersections and building doors.

Either approach works; the choice comes down to look, budget, and how much you want light on faces versus the ground.

Wiring and controls

Commercial bollards and post tops usually run on 120–277V line voltage, wired underground in conduit. Plan the circuit runs and voltage drop on long paths with your electrician. Group fixtures on a photocell or time clock so they come on together, and consider dimming late at night where the site allows.

Low-voltage landscape fixtures run from a transformer and are easier to move, but are generally better suited to accent lighting than to code-required path lighting.

Maintenance

  • Keep lenses clean; dirt and pollen cut output.
  • Trim plants that grow over bollards and path lights.
  • Check for damage after snow plowing and landscaping work.
  • Keep a few spare fixtures so replacements match.

Accessibility and safety

Even path lighting helps people with low vision, and lighting steps, ramps, and curb cuts makes routes safer for everyone. Avoid placing fixtures where they create a trip hazard or block an accessible route.

Common mistakes

  • Spacing bollards too far apart, creating pools of light with dark gaps.
  • Using too much light on paths, which causes glare and makes surrounding areas look darker.
  • Mixing color temperatures across a site.
  • Leaving steps unlit while lighting the flat path.
  • Forgetting the conduit until after paving.

Frequently asked questions

How far apart should bollard lights be?

Commonly about 10–20 ft along a path.

How tall are bollard lights?

Typically 3–4 ft.

What color temperature is best for pathway lighting?

3000K is the most common choice for a warm, welcoming look.

Related

LED bollard lights · Post-top lights · Landscape lighting · Outdoor fixtures · Request a layout · Lighting resources

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare